• 1. Always select correct 'Generation' first before any operation.
  

• 2. Always Use "Scan" if you're working with non dead phone, this will help mobileEx to use 'correct' spesific setting for any phones attached to box.
  

• 3. "BUS Check" with setting safe flash ticked, will perform boot squence, display boot information (upp id, flash manufacture, flash address) and automatically safe phone's rpl.
  

• 4. Make sure phone is in correct mode for any FBUS/NON flashing operation,
  - example: in Tuning & Testing page, phone should be in TEST MODE, else will be best if the phone is in LOCAL MODE.
  Do phone mode change manually if needed.
  

• 5. When doing jobs on working phone, for any operation (add language, locks, etc), DCT4 and BB5, it is better to save its security data (RPL, certificate, pm, etc) first before you do anything else. Just in case...
  

• 6. If you noticed, there was a differences of flashing speed between FlashID/Manufacturer the option 'Fast flash' should not be enabled for "INTEL" flash chip.
  

• 7. If you need only to change the language, select file setting as NORMAL. then check 'Language Only"
  

• 8. "Safe Flash" will save RPL backup from flash mode, and currently NOT supported for ASIC type 11 phone, so dont be checked. For this phone please do a PM backup since RPL backup from flash mode not yet supported. All other DCT4 asic is supported. Yes, even the dead one.
  

• 9. Use "Restart" button every time you need to refresh the connection or restart the phone.
  

• 10. Unlock "Security Code" on all DCT4,DCT4PLUS(Asic 2),WD2, TIKU without loosing any user data(phonebook, msg, etc) even counter already blocked? Yes, it is possible using mobileEx. Just do a "BUS Check" and you will see "Master Code" , use this code as the security code(this code readed from the phone and 100% will work both for CDMA or GSM phones).
  

Run on first time, choose which module to execute

This image has been resized. Click this bar to view the full image. The original image is sized 687x266.

-----------------------
Customizing Your Suite
-----------------------
Configure Nokia Tool

Open Nokia Service Tool, and click on this corner



>

This image has been resized. Click this bar to view the full image. The original image is sized 958x515.

* Enabled Imei changes -> if checked Imei/Esn changes will visible.
Kindly check for your local law for this operation.

* Auto backup ... -> Backup RPL on BUS check ( for DCT4)

* Auto Create DP folder if not exist
This is for directory creation specialy for .nfp extraction. Inside those directory, mcu, ppm, and cnt will be placed.

* Default FBUS timeout
This will set FBUS timeout (higher value = low speed but more accurate)

* Highlight market item
This will highlight the character you choosed. For example on picture, it highlighted on Indo, APAC, MD, and -X.
You will see like this when you selecting files from product code



Server : this is for your ask>rpl service. choose which one is fastest from your location.



And this is the setting for your firmware directory




Nokia Service Tool Configuration:

- Open mobileEx.exe
- Choose interface(UFS/JAF/MTBOX/..), Push "Connect"
- Click on the "star" logo, this is "Appl Modules Loader", Choose "Nokia Service Tool".
- Wait for few second, until Nokia window is loaded.
- Click on "quote" logo (at the right side of the star logo), Choose "Config".
this is the Main Configuration Settings for Nokia.

~General Settings
- Imei Changes
Tick this if you want to use the Imei changes features (check you country law first !!!)
- Auto Backup important data on "BUS Check" (for DCT4 only)
When doing BUS check, RPL will be back up.
- Save as __back.RPL
if you check this, the backup will be generated with timestamp every time you "BUS check", else will only save first time.
- Show Detailed Info
Recommended for Advance User, This will allow to display information log in detail.
- Automaticaly select Generation on "Scan"
Correct Generation will be automaticaly selected when you Scan the phone, for example: if you have DCT4 phone connected but active generation is BB5, after you scan product generation will be set to "DCT4"(Not applicable for DEAD phone')
- Auto create DP folder if not exist
New Folder in "Products\" will be made, if not exists.
- Default FBUS Timeout
Default is 5000 ms= 5 second.
Less=Faster respond but might have problem with phone which has longer booting time(WD2/BB5)
- Highlight Market items.
Usefull for fast select product code for spesific market.
Enter whatever keyword you want, for example if you choose "EURO,UK" then 'Market Name' which contain word: EURO or UK will be highlighted.
~ Server
You could change here the MXKEY server host, someday when we need to change them. Default is: nkrpl.biz
~ Directory
Select "Products" folder in "Data Package 1"(Default=C:\Program Files\Nokia\Phoenix\Products).
Select "Data Package 2" folder in "Data Package 2"(Default=C:\Program Files\Common Files\Nokia)/(Optional)
Select "Wintesla" Directory(Default=C:\Wintesla).

MXKEY v3.4 rev 1.6 - Nokia and Alcatel updates


__________________