chuyển hệ nokia ở đây

2600b to 2600



1. Flash it to 2600
2. Change filters
3. write pm
4. unlock

6010 to 3510i



1. Back up rpl
2. change flash i.c, 3510i or 3530 flash i.c,then
3. add a ram to it
4. flash it to 3510i,,use rh9 v5.35 flash file
5. change the 3 filters the 850/1900 mhz rx and 1900 mhz tx filter,
6. put a jumper from uem to pa
7. write pm
8. unlock

6030b to 6030

6101b to 6101


No software modification is required coz 6101b is already a GSM tri-band
(850_900/1800/1900) but you can also flash it with RM-76 Data Package.

since phone is tuned to 850 MHz otherwise no network or weak network..

write pm (6101)

6103b to 6103

[You must be registered and logged in to see this link.]

No software modification is required
(6103b supports 900mhz)

change 2 filters
then write 6103 PM
unlock

8801 to 8800




1. Change Rx And TX filters
2. write with file 8800_rm13_short.pm

3650 to 3660

1. back up rpl
2. change UPP V2.4 to UPP V3.2
3. flash to 3660 V5.08
4. change uem
5. write special rpl file for 3660
6. write pm
7. unlock
8. replace 3650 keypad to 3660

3595 to 3530



Flash it to 3530 , change 2 filters , write a good pm , unlock it.

3100b rh50 to 3100 rh19



flash it with rh19
write 3100 special pm file for speaker
ui settings.

3200b to 3200



only change filters and write good pm file.

3600 to 3650



change filters

flash the phone with 3650 flash files v3.16 ,write good pm and ui settings.

6800a to 6800



do as in picture.

8390 to 8310



1. Jumper resistor is a resistor (not actually a resistor) with 0 ohm value, usually colored green with 0 markings.
Wire can also be use instead, but must not be very thin and should be as short as possible. Thin and long wire will introduce high inductive reactance and will result to weak received signal.

2. T500 can be taken from 3310 unit. It is located just above HAGAR, refer to your service manual to easily locate it. Also take note to its pin orientation during installation.

Bypassing Z551 with wires is not recommended,this will weaken the receiver sensitivity due to incorrect signal phase relationship.

3. Give special attention when installing VCO, improper positioning will result to no network activity

ngage qd rh47 to ngage qd rh29



DO HARDWARE AS SHOWN IN PICTURE.
1- Erase
2- Flash MCU and PPM (Ngage Qd Rh-29)
3- Write pm
4- Init lock

6102 TO 6101

FOLLOW THE PICTURE.

3390b to 3310






full flash with 3310 firmware and do hardware like in picture.

1100b to 1100



1. erase flash
2. flash with 1100(rh18)
3. change filters
4. write pm
5. unlock

1600b to 1600



1. change 2 filters ( from 1600 )
2. flash it to 1600 rh-64 firmware
3. load 1600pm files
4. unlock

3220b to 3220



change the filters
upload good pm file
unlock it.

2651 to 2650



1. Change filters shown in the picture u can use filters from nokia 3100
2. Full flash with 2650 files(Mcu,ppm,cnt)
3. Write a good pm
4. unlock it.

8390 to 8310



Jumper resistor is a resistor (not actually a resistor)
with 0 ohm value, usually colored green with 0 markings.

Wire can also be use instead, but must not be very thin
and should be as short as possible. Thin and long wire
will introduce high inductive reactance and will result
to weak received signal.


2. T500 can be taken from 3310 unit. It is located just
above HAGAR, refer to your service manual to easily
locate it. Also take note to its pin orientation during
installation.

Bypassing Z551 with wires is not recommended,
this will weaken the receiver sensitivity due to incorrect
signal phase relationship.


3. Give special attention when installing VCO, improper
positioning will result to no network activity

6300b to 6300



just flow the pic..

6061 to 6060


1.full erase
2.flash with (6060v_RH-97_dp_20.00_AMS_EU_sw-3.03) this file
3.write this pm
4.unlock,fectory setting...
5.change 2 filters.u can take from any 1600 or 1110 phone

5300b Convert 100% Solution

1st : make sure u have Certificate Backup
2 : ERASE ( BB5Erase_16MBrap )
3 : ERASE ( BB5Erase_32MBrap )
4 : BB5Erase_8MBrap
5 : full flash u r phone RM-146_DP20_4.00__sw-05.00
6 : write backup pm


simply done.

Successfully converted nokia 1680c-2b


1.t flash your phone with rm394,
version 5.61
2.wirte a 1680c pm file on it
3.change the both signal filter on it